|
|
发表于 2003-1-1 10:42:19
|
显示全部楼层
ham 5628 驱动程序中的readme.txt 这样写道：
ReadMe file for the
Intel?MD563X-HaM V.92 chipset Linux driver
contents:
1. License
2. Release Notes
3. Installation
4. File Descriptions
5. International Users
6. Beta Tester appreciation
7. Security issues
8. Compilation issues
a. Instructions for Debian Users
b. Kernel Source
9. What is the Hamregistry?
10. what's v92 and v44?
11. The Hamregistry tool (for persistance)
12. Known Bugs/Issues
13. Comments, ideas, problems, fixes
-------------------------------------------------------------------------------
1. LICENSE
IMPORTANT - read the file "LICENSE.txt" for the INTEL SOFTWARE LICENSE
AGREEMENT BEFORE COPYING, INSTALLING OR USING.
also note:
The serial driver open source code located in the directory "serialdrv"
is work covered under the GNU GENERAL PUBLIC LICENSE (GPL).
The "serialdrv" directory has the GPL in the file "GPL.txt".
-------------------------------------------------------------------------------
2. Release Notes
This release supports 2.4.x kernels.
This release is not compatible to 2.2.x kernels, please use
the 333-5 Linux HaM driver.
The HaM corecode binary was compiled with gcc version 2.96
v92 support added: modem on hold AT command set,
PCM upstream, v44, and quick connect are implemented.
Linux Compatability tests are performed on the latest or previous
versions of the following distributions: Mandrake, RedHat, and SuSE
-------------------------------------------------------------------------------
3. INSTALLATION
Prerequisites:
1. root access
2. bash shell to run install scripts
3. a HaM modem
4. KERNEL SOURCE HEADERS FOR THE KERNEL YOU ARE RUNNING
(found on your distribution's CD)
6 steps to install
1. login as ROOT
2. extract the archive into a directory with "tar -zxvf <archivename>.tgz"
3. cd into the directory it created.
4. Type: make clean
5. Type: make ham
6. Type: make install
The installation script has been designed for the following distributions
release versions
mandrake-release
SuSE-release
redhat-release
debian_version (including Corel)
slackware-version
conectiva-version
bluepoint-release
Unknown distributions install modules and utilities but
will not install boot scripts!.
Please examine the haminst script if you have a different distribution.
The driver is split in two. A ham serial driver and core driver.
The core driver must be loaded first since the serial driver depends on it.
The serial driver registers itself as character device
major number 240, minor number 1.
The serial driver takes one argument right now, which is a number to
override the default major number if you need to.
ATTENTION: if the driver compiles but the script just wont work for you.
Here are the bare minimum steps to get your modem to work.
0. log in as root.
1. insmod -f hamcore.o
2. insmod -f ham.o
2a. you can start "hamregistry" at this point if you wish.
3. rm /dev/ham
4. mknod /dev/ham c 240 1 (note "240" is the default, if it does not
work see what /proc/devices says ham's major number is)
5. ln -s /dev/ham /dev/modem
6. start a comm application like minicom and use the modem.
7. see section 3 (International Users) for info on setting the correct
country settings.
-------------------------------------------------------------------------------
4. FILE DESCRIPTIONS
haminst installation script to install HaM modules and supporting files
files copied to /lib/modules/(kernel-version)/misc
hamcore.o driver core code module
ham.o pseudo serial driver for HaM, depends on hamcore.o
files copied to /etc/rc.d/... (path differes per distribution)
hamboot boot scrip to start and stop HaM modules
files copied to /usr/sbin
hamregistry hamregistry is the "registry" like tool that the modem uses to
get and store persistant data such as county info and profile strings.
files copied to /etc
hamregistry.bin file that stores the initial persistant data for modem.
-------------------------------------------------------------------------------
5. INTERNATIONAL USERS
hamregistry will store the last country setting you
set in the modem.
in minicom (or equivalent comm application)
the commmand to change country setting is "AT+GCI="
the command takes a t.35 country code in hexadecimal.
below is a list of currently supported t.35 country codes.
you can also put this "AT" command in the init string of
the comm application you are using.
if you are a CTR-21 country I think you should be able to
choose a CTR-21 country on the list and be ok. but
that's no guarantee.
The same goes for countries that are "USA" compatable.
(this table also exist in the source file wwh_dflt.c that
ships with the hamcore driver)
country code t.35 code
---------------------------
USA 1 B5
KOR 82 61
ECU 593 35
BOL 591 14
CHL 56 15
COL 57 27
PAN 507 85
PER 51 88
SAU 966 98
THA 66 A9
VNM 84 BC
SWE 46 A5
DNK 45 31
FIN 358 3C
NOR 47 82
ISL 354 52
IRL 353 57
ISR 972 58
LIE 423 68
ESP 34 A0
TUR 90 AE
DEU 49 42
AUT 43 0A
CHE 41 A6
CYP 357 2D
GRC 30 46
ITA 39 59
LUX 352 69
NLD 31 7B
GBR 44 B4
BEL 32 0F
FRA 33 3D
PRT 351 8B
PAK 92 84
JPN 81 00
RUS 7 B8
AUS 61 09
MYS 60 6C
CHN 86 26
HKG 852 50
SGP 65 9C
NZL 64 7E
ARG 54 07
BRA 55 16
MEX 52 73
TWN 886 E3
IND 91 53
PHL 63 89
IDN 62 54
BHS 103 0B
BRB 104 0E
BMU 105 12
GTM 502 49
HTI 509 4E
HND 504 4F
JAM 1 5B
NIC 505 7F
PRY 595 87
PRI 121 8C
SUR 597 A3
TTO 117 AC
URY 598 B7
VEN 58 BB
ZWE 263 C4
GUY 592 4D
EST 372 E0
HUN 36 51
SVN 386 E2
ARE 971 B3
SVK 421 2E
CAN 107 14
CRI 506 1B
DOM 110 33
SLV 503 37
GMB 220 41
GIB 350 45
POL 48 8A
EGY 20 36
CZE 420 2E
ZAF 27 9F
GUF 594 E1
-------------------------------------------------------------------------------
6. Thanks to the following beta testers for their valuable input and
suggestions during the HaM 333 beta test between January 2 - 26, 2001
Dorian S. Araneda
Sean Walbran
Rob Clark
Marvin Stodolsky
Dominique Duval
Roman Krais
Ulrich Guenther
Marcelino Viana Pinheiro
Thomas S. Iversen
Jospeh Teichman
Michel Bartolone (MED)
Ramon Gonzalez Montoiro
Ryoji Kawagishi
Torsten Vogel
"jandro"
Ian Carr-de Avelon
Helga Weindl
Ed Casas
Bernhard Hoelcker
Alexander "Sasha" Voytov
Albert Woo
Peter Hirschmann
and all of the helpful Linux HaM users
around the world and at www.linmodems.org
-------------------------------------------------------------------------------
7. Security issues
the haminst and hamboot file install the files and device nodes as
root for the owner and group.
this will cause problems for those who want to user the modem to dialout
using an account other than root.
In SuSE, "dialout" is the group used to install the files and device node.
This way, anyone belonging to the "dialout" group can use the modem to dialout.
(take a look at /etc/group)
I did not want the script to allow full access of the modem to everyone without
"root" knowing.
Edit the hamboot and haminst scripts to fit your needs.
-------------------------------------------------------------------------------
8. Compile issues
a. this driver will now compile with the this path:
/lib/modules/<kernel version>/build/include
the 2.4.4+ kernels says to copy the /boot/vmlinuz.version.h
over to the kernel build path. I have the makefile do this
if this file exists. You must install the kernel source
code anyways. It should be on your distribution's CD.
-------------------------------------------------------------------------------
9. What is the Hamregistry?
The hamregistery is an application that stores data for the ham driver onto
the disk. hamregistry stores information from the driver that needs to
persist from reboot to reboot such as you current country setting.
The haminst install script and the hamboot script start this utility
automatically for you.
If this tool is not present when the driver gets used your profile,
quickconnect, and current country setting will not be saved but the driver
should still work fine. The only step that would need to be done is to
make sure that the driver is set to the correct country with
at+gci= (see section 5)
-------------------------------------------------------------------------------
10. What's v92 and v44?
a. modem on hold: (ISP and your ISP dialer must also support this)
This will allow you to pause your ppp connection to answer an incoming
call. You will need call waiting, dialer, and ISP support for this to
work. When you are done with the call you can resume your ppp connection
without having to reconnect. The AT command set for this feature exist
in the driver.
b, pcm upstream:
(ISP must also support this, as of version 4.32 I
dont know any ISP's that do)
This will allow faster upload speeds.
to enable: at+pig=0
to disable: at+pig=1
c. quickconnect:
Once you make a call to a v92 modem, your phoneline characteristics are
stored. Whenever you make a new v92 connection it will use this data
to make the call negotiation quicker (approx 10 seconds).
to enable: at+pqc=0 at+pss=0
to disable: at+pss=2
d. v44: (ISP must also support this)
A better compression protocol than v42 which can give you better transfer
speeds.
-------------------------------------------------------------------------------
11. The Hamregistry tool
The hamregistry tool is used to provide persistance of settings across
reboots. The haminst and hamboot scripts automatically setup and start
the hamregistry background task for the modem to use.
The hamregistry tool has command line arguments for those who wish to
customize persistant settings. To use these command lines
you must first stop the driver with "bash hamboot stop".
Once the driver has been stopped you may run hamregistry with one of these
arguments to store into the /etc/hamregistry.bin persistance file:
(supply value for items in < >)
-mfg <Modem manufactures name>
-mod <Modem model name>
-hookflash <0,1,2>
hookflash method: 0=(default)without tone 1=with tone 2=reserved
-v92rptopt <0,1>
control v92 reporting: 0=PCM upsteam only 1=(default) all v92
-gpio_lpohd <0,1>
Handset Hook detection: 0=not supported 1=(default)supported
-currentcountry <t.35 code>
This info is written to the /etc/hamregistry.bin file.
If hamregistry.bin exists along with the installation files, haminst will
copy it to /etc/hamregistry.bin when installing the modem.
-------------------------------------------------------------------------------
12. Known Bugs/Issues
a. If you see this message
"ham:rs_open: DSP did not reset. try again or restart computer"
and you KNOW you have a HaM modem installed
Disable "PNP OS" in your bios. There is a problem with the driver and
linux PNP. After a time, Linux PNP will disable the card and the driver
currently can not reenable itself.
b. Be aware that the build replaces your
/lib/module/<kernver>//build/include/linux/version.h file with
/boot/vmlinuz.version.h
(this is what Linus T. told me to do with a compiler error)
c. There may be an incompatibility with DevFS. The ham device may be located
in /dev/tts/ham
instead of /dev/ham. Be aware of this and link /dev/modem to the ham
device that corresponds to your setup.
d. SuSE 7.3 has our 412-3 HaM driver on the CD set.
To install it the command is:
rpm -Uhv /cdrom/suse/pay1/Intel-v92ham.rpm
f. There is a compile problem with HaM version 4.25 and SuSe 7.2
remove our comment the line "#define EXPORT_SYMTAB" for it to compile.
e. Incase you are having problems making a ppp connection try using wvidal
with this information below. execute the script and it will have wvdial
make the ppp connection
------my script----------------------
#! /bin/sh
/usr/sbin/pppd -detach lock asyncmap 00000000 \
defaultroute debug /dev/modem 57600 \
ipparam ppp0 linkname ppp0 \
noauth \
connect "/usr/bin/wvdial --chat bellsouth"
------my /etc/wvdial.conf section ---
[Dialer bellsouth]
Modem = /dev/modem
Baud = 57600
Init1 = ATZ
Inti2 = ATQ0 V1 E1 S0=0 &C1 &D2
Dial Command = ATDT
Phone = 6859500
Username = myloginname
Password = mysecretpassword
#Ask Password = 1
Stupid Mode = 0
------------------
-------------------------------------------------------------------------------
13. Comments, ideas, problems, fixes? please contact:
Linux Voice Band Modems (VBM) of Intel Residential Access Division (RAD)
[email protected]
http://developer.intel.com/design/modems/
To restrict email volume, please email only development related issues that are
needed to fix a bug or improve the driver. General questions on how to use the
Linux OS will have to be forwarded.
Other resources and information on Linux controllerless modems can be found on
these usefull sites
http://www.linmodems.org
and
http://linmodems.technion.ac.il
我按说明做了。
1. login as ROOT
2. extract the archive into a directory with "tar -zxvf <archivename>.tgz"
3. cd into the directory it created.
4. Type: make clean
5. Type: make ham
前5步都没有问题。
6. Type: make install
有错误提示： error: can't load ham
Kppp 找不到猫。从超时提示加载 ham.o 失败，加载hamcore.o失败。
然后按以下处理：
0. log in as root.
1. insmod -f hamcore.o
有错误提示。
2. insmod -f ham.o
有错误提示。
2a. you can start "hamregistry" at this point if you wish.
没处理。因为我不知道该怎么处理。
3. rm /dev/ham
没有错误提示。
4. mknod /dev/ham c 240 1 (note "240" is the default, if it does not
work see what /proc/devices says ham's major number is)
生成了 /dev/ham 但是长度为0Byte。
5. ln -s /dev/ham /dev/modem
有乱码输出。
以下不明白如何处理。
6. start a comm application like minicom and use the modem.
7. see section 3 (International Users) for info on setting the correct
country settings.
求助。 |
|
IP卡
狗仔卡
的.也不知道行不行,到现在还没驱动MODEM,敬高手指教!!
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
发表于 2002-11-25 17:19:03