望高手帮助河南网通网通ADSL用户解决LINUX下上网的问题

maghcesar

我是河南网通的ADSL用户(动态IP).我们这里ADSL上网很奇怪:
IP,DNS,网关全部设为自动分配或者不用设置,
开机时,电脑自动从网通的服务器上取一个10.174.xxx.xxx的地址.
这时,只能连接到一个网站,就是网通的,在这里你可以下载一个拨号程序.
运行这个拨号程序 后,电脑会被重新分配一个IP,"61.54.xxx.xxx"
然后,就可以正常上网了.
现在的问题是,网通根本没有提供 for linux 的拨号程序.只有windows下的.
有没有办法在linux下实现上网呢?

我现在装的 MDK9.1 可以正常连接到网通那个下载拨号程序的网址.
其它的都不行.各位有什么办法吗?
-----------下面是那个 for windows 的拨号程序的下载地址-----------
http://218.29.0.252:8080/kuandai/zhinan/setup.exe

至此新春佳节将尽之际,我代表中共中央、全国人大、国务院、
全国政协、中央军委及我个人向你及你的家人祝贺新年.
祝你们新年快乐,万事如意!
并预祝高手们能顺利解决这个难题!为抗议网通的独断行为做出应有的贡献!

hotboy1000

用LINUX下面的ADSL拨号工具代替你那个程序。
我在上海试过的，你去试试，或许能行。
如果好了，回复一下。

killxp

估计没用的,猜想是否可以用sniffer看看到底这个专用拨号软件的发包内容.

hotboy1000

除非局端做了设置，不然所有的PPPOE都是一样可以用的。

killxp

哈哈,肯定不是标准的PPPOE了,在红旗LINUX论坛已经讨论过了啊.

hotboy1000

哦，我在上海的小区也遇到过这样的问题，一拨就好了，比ADSL还爽了。

killxp

试试 PPPOE-SNIFF
Section: Maintenance Commands (
Updated: 3 July 2000

   
NAME
pppoe-sniff - examine network for non-standard PPPoE frames   
SYNOPSIS
pppoe-sniff [options]
  

DESCRIPTION
pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe( to work.
Some DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field. It is often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.

To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)

If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the Ethernet hub. Plug two computers into normal ports on the hub. On one computer, run whatever software the DSL provider gave you on whatever operating system the DSL provider supports. On the other computer, run Linux and log in as root.

On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff. If the ethernet interface is eth0, for example, type these commands:


        ifconfig eth0 promisc
        pppoe-sniff -I eth0

On the other machine, start your DSL connection as usual. After a short time, pppoe-sniff should print recommendations for the value of PPPOE_EXTRA. Set this value in /etc/ppp/pppoe.conf. If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-mail this to [email protected] along with the name of your ISP and the manufacturer and model number of your DSL modem. This information will be collated and provided on the PPPoE web page for users who do not have two computers.

After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:


        ifconfig eth0 -promisc

  

OPTIONS
-I interface
The -I option specifies the Ethernet interface to use. Under Linux, it is typically eth0 or eth1. The interface should be "up" and in promiscuous mode before you start pppoe-sniff.

-V
The -V option causes pppoe-sniff to print its version number and exit.

  
BUGS
pppoe-sniff only works on Linux.
  

AUTHORS
pppoe-sniff was written by David F. Skoll <[email protected]>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.

  

SEE ALSO
adsl-start(, adsl-stop(, adsl-connect(, pppd(, pppoe.conf(5), pppoe(, adsl-setup(, adsl-status(, pppoe-server(, pppoe-relay(8)

panjun10

更简单的方法。。。用wine.............

lantian

现在河南网通已经在推出了Linux客户端程序。
下载地址：
http://218.29.0.252/ecou_for_linux_install.zip