|
|
发表于 2003-12-21 21:48:04
|
显示全部楼层
grub.conf
title Fedora Core (2.4.22-1.2115.nptl)
root (hd0,10)
kernel /boot/vmlinuz-2.4.22-1.2115.nptl ro root=LABEL=/ hdd=ide-scsi rhgb vga=0x317 append="video=vesa:ywrap,mtrr"
initrd /boot/initrd-2.4.22-1.2115.nptl.img | 640x480 800x600 1024x768 1280x1024
----+-------------------------------------
256 | 0x301 0x303 0x305 0x307
32k | 0x310 0x313 0x316 0x319
64k | 0x311 0x314 0x317 0x31A
16M | 0x312 0x315 0x318 0x31B
vesafb.txt
What is vesafb?
===============
This is a generic driver for a graphic framebuffer on intel boxes.
The idea is simple: Turn on graphics mode at boot time with the help
of the BIOS, and use this as framebuffer device /dev/fb0, like the m68k
(and other) ports do.
This means we decide at boot time whenever we want to run in text or
graphics mode. Switching mode later on (in protected mode) is
impossible; BIOS calls work in real mode only. VESA BIOS Extensions
Version 2.0 are required, because we need a linear frame buffer.
Advantages:
* It provides a nice large console (128 cols + 48 lines with 1024x76
without using tiny, unreadable fonts.
* You can run XF68_FBDev on top of /dev/fb0 (=> non-accelerated X11
support for every VBE 2.0 compliant graphics board).
* Most important: boot logo :-)
Disadvantages:
* graphic mode is slower than text mode...
How to use it?
==============
Switching modes is done using the vga=... boot parameter. Read
Documentation/svga.txt for details.
You should compile in both vgacon (for text mode) and vesafb (for
graphics mode). Which of them takes over the console depends on
whenever the specified mode is text or graphics.
The graphic modes are NOT in the list which you get if you boot with
vga=ask and hit return. The mode you wish to use is derived from the
VESA mode number. Here are those VESA mode numbers:
| 640x480 800x600 1024x768 1280x1024
----+-------------------------------------
256 | 0x101 0x103 0x105 0x107
32k | 0x110 0x113 0x116 0x119
64k | 0x111 0x114 0x117 0x11A
16M | 0x112 0x115 0x118 0x11B
The video mode number of the Linux kernel is the VESA mode number plus
0x200.
Linux_kernel_mode_number = VESA_mode_number + 0x200
So the table for the Kernel mode numbers are:
| 640x480 800x600 1024x768 1280x1024
----+-------------------------------------
256 | 0x301 0x303 0x305 0x307
32k | 0x310 0x313 0x316 0x319
64k | 0x311 0x314 0x317 0x31A
16M | 0x312 0x315 0x318 0x31B
To enable one of those modes you have to specify "vga=ask" in the
lilo.conf file and rerun LILO. Then you can type in the desired
mode at the "vga=ask" prompt. For example if you like to use
1024x768x256 colors you have to say "305" at this prompt.
If this does not work, this might be because your BIOS does not support
linear framebuffers or because it does not support this mode at all.
Even if your board does, it might be the BIOS which does not. VESA BIOS
Extensions v2.0 are required, 1.2 is NOT sufficient. You will get a
"bad mode number" message if something goes wrong.
1. Note: LILO cannot handle hex, for booting directly with
"vga=mode-number" you have to transform the numbers to decimal.
2. Note: Some newer versions of LILO appear to work with those hex values,
if you set the 0x in front of the numbers.
X11
===
XF68_FBDev should work just fine, but it is non-accelerated. Running
another (accelerated) X-Server like XF86_SVGA might or might not work.
It depends on X-Server and graphics board.
The X-Server must restore the video mode correctly, else you end up
with a broken console (and vesafb cannot do anything about this).
Refresh rates
=============
There is no way to change the vesafb video mode and/or timings after
booting linux. If you are not happy with the 60 Hz refresh rate, you
have these options:
* configure and load the DOS-Tools for your the graphics board (if
available) and boot linux with loadlin.
* use a native driver (matroxfb/atyfb) instead if vesafb. If none
is available, write a new one!
* VBE 3.0 might work too. I have neither a gfx board with VBE 3.0
support nor the specs, so I have not checked this yet.
Configuration
=============
The VESA BIOS provides protected mode interface for changing
some parameters. vesafb can use it for palette changes and
to pan the display. It is turned off by default because it
seems not to work with some BIOS versions, but there are options
to turn it on.
You can pass options to vesafb using "video=vesa ption" on
the kernel command line. Multiple options should be separated
by comma, like this: "video=vesa:ypan,invers"
Accepted options:
invers no comment...
ypan enable display panning using the VESA protected mode
interface. The visible screen is just a window of the
video memory, console scrolling is done by changing the
start of the window.
pro: * scrolling (fullscreen) is fast, because there is
no need to copy around data.
* You'll get scrollback (the Shift-PgUp thing),
the video memory can be used as scrollback buffer
kontra: * scrolling only parts of the screen causes some
ugly flicker effects (boot logo flickers for
example).
ywrap Same as ypan, but assumes your gfx board can wrap-around
the video memory (i.e. starts reading from top if it
reaches the end of video memory). Faster than ypan.
redraw scroll by redrawing the affected part of the screen, this
is the safe (and slow) default.
vgapal Use the standard vga registers for palette changes.
This is the default.
pmipal Use the protected mode interface for palette changes.
mtrr setup memory type range registers for the vesafb framebuffer.
vram:n remap 'n' MiB of video RAM. If 0 or not specified, remap memory
according to video mode. (2.5.66 patch/idea by Antonino Daplas
reversed to give override possibility (allocate more fb memory
than the kernel would) to 2.4 by [email protected])
Have fun!
Gerd
--
Gerd Knorr <[email protected]>
Minor (mostly typo) changes
by Nico Schmoigl <[email protected]> |
|
IP卡
狗仔卡
发表于 2003-12-20 22:36:52
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡