Problem with FC2&OpenSSI

rgt

I tried to set up a simple cluster with two nodes, the configuration scenario
is set as:

Node 1: IBM Thinkpad A22p, PIII 1.0g, 512M mem
Dual boot system, Win2K/FC2
  
For FC2:  
dev/hda3     /boot  1024M ext3
dev/hda5     /      5000M ext3
dev/hda6     swap   1024   
dev/hda7     /drdb  585   ext3
  
OpenSSI: openssi-fc2-1.2.2.i686
Node 1: Static IP: 192.168.1.100
Firewall disabled
PXE
Root failover is enabled for node1, however, didnot install drbd-ssi-1.2.2

After node1 is booted up(with KDE started), use
'usr/sbin/openssi-config-node' to add a new node (2).
  
  
Node 2: IBM Thinkpad G40, P4 3.0g cpu, 1g mem  
Originally Win2K is installed, use partition magic to resize the disk and set
up linux partitions as:
  
dev/hda3     /boot  1024M ext3
dev/hda5     /      3400M ext3
dev/hda6     swap   2048   
dev/hda7     /drdb  585   ext3
  
PXE, 192.168.1.2
root failover is disabled
  
In node1, after run 'openssi-config-node' to add node 2, it is said:
"All new nodes are allowed to join the cluster. If you wish to setup a
local boot device for a node, wait until it's fully up, create a Linux
filesystem on one of its local disks using fdisk and mkfs, then run
ssi-chnode to configure the filesystem as a local boot device."

Then I begin to boot node2, after it loading kernal, it will halt forever, and
I will never receive a 'nodeup'
message in node 1, and when I use 'cluster -v', I can only see '1: UP', node 2
is unavailable.

The message in the scree of node2 is listed as:

"CPU: L2 cache: 512K
CPU: Hyper-Threading is disabled
Interl machine check reporting enabled on CPU#0.
CPU0: Intel(R) Pentuum(R) 4 CPU 4.00GHz stepping 07
per-CPU timeslice cutoff: 1462.86 usecs.
task migration cache decay timeout: 10msecs.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Starting migration thread for cpu 0
smp_num_cpus:1
ACPI: Subsystem revision 20031002
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd966, last bus=5
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux Net4.0 for linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)"

After this message is displayed, node2 will hang there forever, I don't know
what is wrong with it. I used a  
USB optical mouse with node2, some people guess that is the reason. However,
even I unplug the USB mouse, I got  
exactly the same result.  

Anyone have similar experience on this? your advice will be highly
appreciated, thanks a lot!  

Also, I have update the BIOS of the second node(IBM G40) to the newest version, but it doesnot help. Really feel crazy for this, could anyone give me a hint? Thanks!!!